| Jetway NF9W Mini-ITX Motherboard |
| Processor | Intel® Celeron N2930 SoC, 1.83GHz – 2.16GHz Burst, Quad-Core, 7.5W TDP/4.5W SDP |
| Memory | 1 x 204-pin DDR3L-1333 SO-DIMM up to 8GB (1.35V required) |
| Graphics | Intel HD Graphics, 313MHz - 854MHz |
| Audio | Realtek ALC662 HD Audio with 3W Amplifier
Realtek ALC888 HD Audio with 3W Amplifier (Manufacturered after March 2021) |
| LAN | 1 x Realtek RTL8111G Gigabit Ethernet with Enhanced Surge Protection
1 x Realtek RTL8111H Gigabit Ethernet with Enhanced Surge Protection (Manufacturered after March 2021) |
| Storage | 2 x SATA3 6Gb/s Connector
2 x SATA2 3Gb/s Connector |
| Super IO | FINTEK F81768D-I |
| Back Panel Connectors |
1 12V DC-In jack
1 USB 3.0
3 USB 2.0
1 DVI-I
1 Serial port (RS232/422/485)
1 RJ45 LAN (10/100/1000)
1 3.5mm Line-out jack
|
| Onboard I/O Connectors |
1 PCI Express x1 Slot
1 Full size mini PCI-E Slot
2 SATA3 6Gb/s Connectors
2 SATA2 3Gb/s Connectors
3 USB Pin Headers for up to 5 additional USB 2.0 Ports
1 RS232 Serial Port Header
1 24-bits Dual Channel LVDS connector/Inverter
1 AT/ATX power switch mode select jumper
1 Chassis Intrusion Header
1 5-pin SMBUS(I2C) Header
1 8-bit GPIO Header
1 9-pin Audio Header
1 2-pin LAN LED Header
1 9-pin Front Panel Header
1 4-pin Speaker Header
3 4-pin Fan Headers
1 2-pin SPDIF Out Header
1 2-pin MON_PWR Out Connector
2 4-pin SATA Power Out Connector (Male)
1 2-pin +12V Alternate Power Connector (Molex 5566-2)
|
| Power Supply for NF9W |
External Power Supply – the board can be powered with a 12V external power supply though a DC connector on the back panel. The rear 12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is 12V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal 12V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +12 (±10%) VDC. The internal 1 x 2 power connector is a Molex 5566-2 header which accepts a Molex 5557-02R connector from the power supply.
Caution: There is no isolation circuitry between the external 12V DC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external 12V DC jack is covered if the internal 1 x 2 power connector is to be used.
|
| Market Segments Supported |
√ Digital Security & Surveillance
√ All-in-One (AIO)
√ Panel PC
√ Industrial Automation/Control
√ Media & Storage Server
√ Medical
√ Thin Client
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
|
