| Jetway NF9M Mini-ITX Motherboard |
| Processor | Intel® Celeron N2930 SoC, 1.83GHz – 2.16GHz Burst, Quad-Core, 7.5W TDP/4.5W SDP
Intel® Atom E3827 SoC, 1.75GHz, Dual-Core, 8W TDP, with AES-NI support |
| Memory | 2 x 204-pin SODIMM DDR3L-1333 Single Channel (up to 8 GB) |
| Graphics | Intel HD Graphics, 313MHz - 854MHz for N2930
Intel HD Graphics, 542MHz - 792MHz for E3827 |
| Audio | Realtek ALC662 HD Audio with 3W Amplifier
Realtek ALC888 HD Audio with 3W Amplifier (Manufacturered after April 2021) |
| LAN | 1 x Realtek RTL8111G Gigabit Ethernet with Enhanced Surge Protection
1 x Realtek RTL8111H Gigabit Ethernet with Enhanced Surge Protection (Manufacturered after April 2021) |
| Storage | 2 x SATA2 3Gb/s Connectors
1 x Full-size mSATA slot |
| Super IO | FINTEK F81866A |
| Back Panel Connectors |
1 +9V ~ +36V DC-in jack
1 USB 3.0
1 DVI-I
1 COM port (RS232/422/485)
1 RJ45 LAN (10/100/1000)
3 USB 2.0
1 3.5mm Audio Jacks (Line Out)
|
| Onboard I/O Connectors |
1 PCI Express x1 Slot
1 Full size mSATA Slot (shares with one SATA)
1 Full size mini PCI-E Slot (R20 version)
2 SATA2 3Gb/s Connectors
1 USB 3.0 Pin Headers for up to 2 additional USB 3.0 Ports
1 USB 2.0 Pin Headers for up to 2 additional USB 2.0 Ports
3 Serial Port Headers (RS232, +5V/+12V)
1 24-bits Dual Channel LVDS connector/Inverter
1 GPIO header
1 Chassis Intrusion header
1 AT/ATX Mode jumper
1 PS/2 Mouse/Keyboard header
1 Parallel header
1 9-pin Audio header
1 2-pin LAN LED header
1 2-pin SPDIF header
1 4-pin SMBUS header
1 Front Panel header
3 Fan headers
1 4-pin Power Output (Male)
1 2-pin +9V ~ +36V Alternate Power connector (Molex 5566-2)
|
| Power Supply for NF9M |
External Power Supply – the board can be powered with a +9V ~ +36V external power supply though a DC connector on the back panel. The rear +9V ~ +36V VDC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +9V ~ +36V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +9V ~ +36V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +9 ~ +36 VDC.
Caution: There is no isolation circuitry between the external +9V ~ +36V DC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +9V ~ +36V DC jack is covered if the internal 1 x 2 power connector is to be used.
|
| Market Segments Supported |
√ Digital Signage
√ Panel PC
√ Industrial Automation/Control
√ All-In-One
√ Retail (POS/Kiosk/ATM)
√ Casino Gaming
√ Thin Client
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
|
