| Jetway NF591 Mini-ITX Motherboard |
| Processor | Fanless Intel® Celeron N3160 SoC, 1.60GHz – 2.24GHz Burst, Quad-Core, 6W TDP/4W SDP, with AES-NI support
Fanless Intel® Celeron N3150 SoC, 1.60GHz – 2.08GHz Burst, Quad-Core, 6W TDP/4W SDP, with AES-NI support |
| Memory | 2 x 204-pin SODIMM DDR3L-1600 Dual Channel 1.35V required (up to 8 GB)
* 1600MHz memory will run at 1600MHz
* 1333MHz memory will run at 1066MHz
* 1066MHz memory not supported |
| Graphics | Intel HD Graphics, 320MHz - 640MHz |
| Audio | Realtek ALC662 HD Audio with 3W Speaker Amplifier
Realtek ALC888 HD Audio with 3W Speaker Amplifier (Manufacturered after April 2021) |
| LAN | 2 x Realtek RTL8111G Gigabit Ethernet with Enhanced Surge Protection
2 x Realtek RTL8111H Gigabit Ethernet with Enhanced Surge Protection (Manufacturered after April 2021) |
| Storage | 2 x SATA3 6Gb/s Connectors
1 x M.2 slot (M or B+M key-2242/2260/2280 SATA SSD, shared with SATA2) |
| Super IO | FINTEK F81866A |
| Back Panel Connectors |
1 +12V 2.5MM Diameter Locking DC Power Jack
4 USB 3.0
1 DVI-D
1 Serial port (RS232/422/485)
2 RJ45 LAN (10/100/1000)
|
| Onboard I/O Connectors |
1 PCI Express x1 Slot
1 Full size M.2 Slot (SATA only, M key-2242/2260/2280)
1 Full size mini PCI-E Slot
2 SATA3 6Gb/s Connectors
2 USB 2.0 Pin Headers for up to 3 additional USB 2.0 Ports
5 Serial Port Headers (RS232, +5V/+12V)
1 24-bits Dual Channel LVDS connector/Inverter
1 GPIO header
1 Chassis Intrusion header
1 AT/ATX Mode jumper
1 PS/2 Mouse/Keyboard header
1 9-pin Audio header (Line Out & MIC)
2 2-pin LAN LED header
1 VGA header
1 4-pin 3W Amplified speaker header (Left+Right)
1 5-pin SMBUS header
1 Front Panel header
3 Fan headers
1 SIM Card Socket
1 4-pin Power Output (Male)
1 2-pin +12V Alternate Power connector (Molex 5566-2)
|
| Power Supply for NF591 |
External Power Supply – the board can be powered with a +12V external power supply though a DC connector on the back panel. The rear +12V VDC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +12 VDC.
Caution: There is no isolation circuitry between the external +12V DC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 1 x 2 power connector is to be used.
|
| Market Segments Supported |
√ Digital Signage
√ Panel PC
√ Industrial Automation/Control
√ All-In-One
√ Retail (POS/Kiosk/ATM)
√ Casino Gaming
√ Thin Client
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
|
