Jetway NF551 Motherboard |
Processor | Intel® Core i5-6300U, 2.4GHz, 3.0GHz Burst, Dual-core, Hyper-Threading , vPro, Virtualization, 14nm, 15W (Formerly Skylake U) |
Memory | 2 x 260-pin DDR4-2133 SO-DIMM Dual Channel up to 32GB |
Graphics | Intel HD Graphics 520, 300MHz - 1.0GHz |
Audio | Intel® Display Audio via DP |
LAN | 1 x Intel i219-LM PHY Gigabit LAN (iAMT 11) 1 x Intel i211-AT PCI-E Gigabit LAN 4 x Intel i350-AM4 PCI-E Gigabit LAN |
Storage | 1 x SATA3 6Gb/s 1 x 2.5” SATA3 6Gb/s Cableless Drive Bay 1 x mSATA/Mini-PCIE Shared Slot (Full-size) |
Super IO | FINTEK F81803U |
Back Panel Connectors |
1 RJ45 Type Serial port
2 USB 3.0
6 RJ45 LAN (10/100/1000)

|
Front Panel Connectors |
1 GPIO port
2 USB 3.0
2 USB 2.0
2 DP 1.2 (4096 * 2304 @ 60Hz )
1 Power LED & HDD LED
1 Reset Button
1 Power Button
1 12V Locking DC-in jack

|
Onboard I/O Connectors |
1 mSATA/Mini PCI-E Slot (Full-size)
1 Mini PCI-Express Slot (Full-size)
1 SATA3 6Gb/s Connector
1 SATA3 6Gb/s 7+15Pin 90 degree connector
1 USB Pin Header for up to 2 additional USB 2.0 Ports
1 Serial Header (1 * RS232/422/485)
1 SIM Card Holder
1 Chassis Intrusion Jumper
1 AT/ATX Mode Jumper
1 5-pin SMBUS Header
1 7-pin PS2 Keyboard Mouse Header
1 9-pin Front Panel Header
1 4-pin Fan Headers
1 2-pin Internal Power connector (Molex 5566-2)
1 SATA Power connector
|
Form Factor for NF551 |
Proprietary Form Factor (166mm x 138mm) |
Power Supply for NF551 |
External Power Supply – the board can be powered with a +12V external power supply though a DC connector on the back panel. The rear +12V DC jack accepts locking plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +12 VDC. The internal 1 x 2 power connector is a Molex 5566-2 header which accepts a Molex 5557-02R connector from the power supply.
Caution: There is no isolation circuitry between the external +12V DC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 1 x 2 power connector is to be used.
|
Market Segments Supported |
√ Banking ATM
√ Commerce
√ Digital Signage
√ Industrial Automation/Control
√ Industrial Panel PC
√ Retail (POS/Kiosk)
√ Networking/Storage Server/Mail Server/Print Server
√ Telecom
√ Transportation
|
Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
|