| Jetway NF542 Motherboard |
| Processor | Intel® Core i5-4300U, 1.90GHz – 2.90GHz Burst, 2-Core 4-Thread, 15W TDP, vPro |
| Memory | 2 x 204-pin DDR3L-1600 SO-DIMM Dual Channel up to 16GB |
| Graphics | Intel HD Graphics 4400, 200MHz - 1.1GHz |
| Audio | Realtek ALC662 HD Audio, 4-pin 3W 4OHM Stereo Amplifier header (Left+Right) |
| LAN | 1 x Intel i218LM PHY Gigabit LAN (iAMT 9.5)
1 x Intel i211AT PCI-E Gigabit LAN |
| Storage | 1 x SATA3 6Gb/s Cable-Free Connector, 2.5" Drive Connector
1 x Shared mSATA/mini-PCI Express Combo Slot (Full-size) |
| Super IO | FINTEK F81768D-I |
| Back Panel Connectors |
1 Line-out and MIC
2 Serial Port (RS232)
2 RJ45 LAN (10/100/1000)
2 USB 3.0
2 USB 2.0
1 HDMI (3280 x 2000 @ 60Hz)
1 DP (3200 x 2000 @ 60Hz)
1 Reset Button
1 +12V 2.5MM Diameter Locking DC Power Jack
|
| Onboard I/O Connectors |
1 SATA3 6Gb/s Cable-Free Connector
1 Shared mSATA/mini-PCI Express Combo slot (full-size)
1 Mini-PCI Express slot (full-size)
1 PCI Express 2.0 x1 side-slots, Supports Jetway GEN3 Daughter Boards
1 PCI Express 2.0 x4 side-slots, Supports Jetway GEN3 Daughter Boards
1 USB Pin Header for 2 USB 2.0 Ports (2.0 mm pitch)
1 SIM Card Socket
1 8 bit GPIO Header
1 AT/ATX Mode jumper
1 4-pin 3W Stereo Amplifier header (Left+Right)
1 Chassis Intrusion header
1 Front Reset/Power Header
1 4-pin Fan Header
1 2-pin +12V Alternate Power connector (Molex 5566-2)
|
| Form Factor for NF542 |
|
Proprietary Form Factor (110mm x 167mm)
|
| Power Supply for NF542 |
External Power Supply – the board can be powered with a +12V external power supply though a DC connector on the back panel. The rear +12V DC jack accepts locking plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V DC 1 x 2 power connector, where pin 1 is GND and pin 2 is +12 VDC.
Caution: There is no isolation circuitry between the external +12V DC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 1 x 2 power connector is to be used.
|
| Market Segments Supported |
√ Digital Security & Surveillance
√ Digital Signage
√ Gaming
√ Industrial Automation/Control
√ Medical
√ Retail (POS/Kiosk/ATM)
√ Networking/Storage Server/Mail Server/Print Server
√ Thin Client
√ HTPC
|
