| Model Name | NC8H |
| Part Number | JNC8H-IH310 |
| Form Factor | Mini-ITX (170 x 170mm) |
| Processor | 8th & 9th Gen Intel® Core i7 / i5 / i3 / Pentium Processor up to 65W
Socket LGA 1151 (Formerly Coffee Lake) |
| Chipset | Intel H310 |
| Memory | 2 x 260-pin SODIMM un-buffered DDR4-2666 up to 64GB Total
* Core i3, Pentium, and Celeron can only support DDR4-2400 up to 32GB Total |
| Graphics | Requires Intel Core processor with Intel HD Graphics |
| Audio | Realtek ALC662 HD Audio
Realtek ALC888 or ALC897 HD Audio (Manufacturered after March 2021) |
| LAN | 1 x Intel I219-V PHY Gigabit LAN
1 x Intel I211-AT PCI-E Gigabit LAN |
| Storage | 1 x SATA3 6Gb/s
1 x M.2 Slot (M-key, SATA, 2242) |
| Super IO | ITE IT8785E |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware |
| Back Panel Connectors |
1 12 ~ 24V DC-in Jack (1-pin 2.5mm ID, 5.5mm OD)
1 VGA (1920 * 1200 @ 60Hz)
1 HDMI 1.4 (4096 * 2160 @ 30Hz)
4 USB 3.1 Gen 1 (5 Gb/s)
2 RJ45 LAN (10/100/1000)
2 3.5mm Audio Jack
|
| Onboard I/O Connectors |
1 PCI-E x4 Slot
1 M.2 Slot (M-key, SATA, 2242)
1 M.2 Slot (E-key, 2230, for WiFi CNVi)
1 SATA3 6Gb/s Connectors
3 USB Pin Header for up to 5 additional USB 2.0 Ports
4 Serial Headers (RS232)
1 40-pin 4-Lane eDP (4096 * 2304 @ 60Hz)
1 30-pin 24-bits Dual Channel LVDS/Inverter (1920 * 1080 @ 60Hz)
1 Chassis Intrusion Jumper
1 AT/ATX Mode Jumper
1 8-bit GPIO Header
1 6-pin PS2 Keyboard Mouse Header
1 9-pin Audio Header
1 4-pin 3W Amplifier Header
1 5-pin SMBUS Header
1 9-pin Front Panel Header
2 4-pin Fan Headers
1 2-pin +12 ~ 24V Alternate Power-in
1 4-pin SATA Power-out Connector
|
| Power Supply for NC8H |
External Power Supply – the board can be powered with a +12 ~ 24V external power supply though a DC connector on the back panel. The rear +12 ~ 24V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12 ~ 24V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12 ~ 24V 2-pin power connector, where pin 1 is +12 ~ 24V and pin 2 is GND. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 plug from the power supply.
Caution: There is no isolation circuitry between the external +12 ~ 24V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12 ~ 24V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Digital Security & Surveillance
√ Digital Signage
√ Gaming
√ Industrial Automation/Control
√ Medical
√ Retail (POS/Kiosk/ATM)
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
|
