| Model Name | MI97R |
| Part Number | MI97R-30 | MI97R-32 |
| Form Factor | Mini ITX (170 x 170mm) |
| Processor | Intel® Celeron N2930 SoC, 1.83GHz – 2.16GHz Burst, Quad-Core, 7.5W TDP |
| Memory | 1 x 204-pin DDR3L-1333 SO-DIMM up to 8GB (1.35V required) |
| Graphics | Intel HD Graphics, 313MHz - 854MHz |
| Audio | Realtek ALC888S HD Audio |
| LAN | 1 x Realtek RTL8119I PCI-E Gigabit LAN |
| Storage | 1 x SATA2 3Gb/s Connector
1 x M.2 SATA M-key 2242/2280 length |
| Super IO | FINTEK F81966D |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware | Intel fTPM 2.0 (PTT) Trusted Computing Firmware
Onboard NUVOTON TPM v2.0 |
| Back Panel Connectors |
1 +12V 2.5mm Diameter DC Power Jack
1 HDMI (1920 * 1200 @ 60Hz)
1 VGA (1920 * 1080 @ 60Hz)
1 Parallel
3 USB 2.0
1 PS2 Mouse/Keyboard Combo
2 Serial Ports (1 * RS232, 1 * RS232/422/485)
1 RJ45 LAN (10/100/1000)
1 USB 3.0
2 3.5mm Audio Jack (Line Out & MIC In)
|
| Onboard I/O Connectors |
1 PCI-E x1 Slot
1 SATA2 3Gb/s Connector
1 M.2 M-Key, 2242/2280, SATA
1 M.2 E-key, 2230, for WiFi (USB 2.0/PCIE x1)
1 M.2 B-Key, 3042, with SIM Slot (USB 2.0)
3 Serial Headers (RS232)
2 USB Pin Headers for up to 4 additional USB 2.0 Ports
1 40-pin eDP (2560 * 1600 @ 60Hz) OR 24-bits Dual Channel LVDS/Inverter (1920 * 1200 @ 60Hz)
1 8 bit GPIO Header
1 AT/ATX Mode Jumper
1 9-pin Front Audio Header
1 5-pin SMBUS Header
1 4-pin Fan Header
1 4-pin SATA Power Output (Male)
1 2-pin +12V Alternate DC-in (Mating plug: Molex 5557-02R)
|
| Power Supply for MI97R |
External Power Supply – the board can be powered with a +12V external power supply though a DC connector on the back panel. The rear +12V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V 2-pin power connector, where pin 1 is +12V and pin 2 is GND. The internal 2-pin power connector is a Molex 5566-2 header which accepts a Molex 5557-02R connector from the power supply.
Caution: There is no isolation circuitry between the external +12V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Industrial PC
√ Factory Automation
√ Retail (POS/Kiosk/ATM)
√ Panel PC
√ IoT
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|
