| Model Series | MI215 |
| Part Number | MI215Q6700
MI215Q6702 (Onboard TPM 2.0) | MI215R6800
MI215R6802 (Onboard TPM 2.0) |
| Form Factor | Mini ITX (170 x 170mm) |
| Processor | Intel® 12th / 13th / 14th Gen Processors up to 65W and IccMax 180A
Socket LGA 1700 (Formerly Alder Lake-S / Raptor Lake-S / Raptor Lake Refresh) |
| Chipset | Intel Q670E | Intel R680E |
| Memory | 2 x Dual Channel Non-ECC DDR5-5600 SODIMM up to 96GB
* 12th Gen CPU only supports DDR5-4800 | 2 x Dual Channel ECC/Non-ECC DDR5-5600 SODIMM up to 96GB
* 12th Gen CPU only supports DDR5-4800 |
| Graphics | Requires Intel Processor with Graphics or a PCIe Graphics Card |
| Audio | Realtek ALC888S HD Audio |
| LAN | 1 x Intel I225-V 2.5GbE
1 x Intel I225-LM PCIe 2.5GbE (Support iAMT) |
| Storage | 2 x SATA3 6Gb/s for RAID 0/1
1 x M.2 2242 (SATA & PCIe 4.0 x4 NVMe, M-key)
1 x M.2 2280 (SATA & PCIe 3.0 x4 NVMe, M-key) |
| Super IO | FINTEK F81966D |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware
Onboard NUVOTON TPM v2.0 for MI215Q6702 and MI215R6802 |
| Back Panel Connectors |
4 USB 3.2 Gen 2 (10 Gb/s)
2 RJ45 2.5GbE LAN (10/100/1000/2500)
2 HDMI 2.0b (4096 x 2160 @ 60Hz)
2 DP 1.4a (4096 x 2304 @ 60Hz)
1 3.5mm Line-out/MIC-in Jack
1 12V ~ 36V DC-in Jack (4-pin Mini-DIN)
|
| Onboard I/O Connectors |
1 PCIe 4.0 x16 Slot (x16 or x8/x8 Bifurcation, Max. 70W)
2 SATA3 6Gb/s Connector for RAID 0/1
1 M.2 M-Key, 2242 (PCIe 4.0 x4 NVMe and SATA)
1 M.2 M-Key, 2280 (PCIe 3.0 x4 NVMe and SATA)
1 M.2 E-key, 2230 (USB2.0 and PCIe 3.0 x1 CNVi WiFi)
1 M.2 B-key, 3042 3052 (USB3.2/2.0 and PCIe 3.0 x1 for Cellular)
1 USB Header for 2 additional USB 3.2 Gen 1 (5 Gb/s)
2 USB Headers for 4 additional USB 2.0 Ports
6 Serial Headers (4 * RS232, 2 * RS232/422/485)
1 Combo 24-bits Dual Channel LVDS or eDP connector (Max 1920x1200 @60Hz)
1 Nano SIM Socket (on bottom)
1 8 bit GPIO Header
1 AT/ATX Mode Jumper
1 9-pin Front Audio Header
1 5-pin SMBUS Header
1 Fan Header
1 4-pin Alternate Power-in Connector
|
| Power Supply for MI215 |
External Power Supply – the board can be powered with a +12V ~ +36V external power supply though a DC connector on the back panel. The rear +12V ~ +36V DC jack accepts plugs with a 4-pin Mini-DIN connector.
Internal Power Supply – the board can alternatively be powered via the internal +12V ~ +36V DC 2 x 2 power connector, where pins 1 and 2 are +12V ~ +36V (±5%) DC and pins 3 and 4 are GND. The connector used is Molex Micro-Fit (3mm pitch), right-angled, 4-pos/dual row (2x2).
Caution: There is no isolation circuitry between the external +12V ~ +36V DC jack and the internal 2 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V ~ +36V DC jack is covered if the internal 2 x 2 power connector is to be used.
|
| Market Segments Supported |
√ Edge Computing
√ Digital Signage
√ Industrial PCs
√ Factory Automation
√ Public Sector
√ Digital Security
√ Surveillance Application
|
| Environment |
Operating Temperature : 0 ~ 60°C (with 0.7m/s air flow)
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|
