| Model Name | MI09 |
| Part Number | MI09-30 | MI09-32 |
| Form Factor | Mini ITX (170 x 170mm) |
| Processor | 10th Gen Intel® Core i9 / i7 / i5 / i3 / Pentium / Celeron Processor up to 65W
11th Gen Intel® Core i9 / i7 / i5 Processor up to 65W
Socket LGA 1200 (Formerly Comet Lake and Rocket Lake) |
| Chipset | Intel H470 |
| Memory | 2 x 260-pin SODIMM Dual Channel DDR4-2933 up to 64GB Total
* Core i9 / i7 CPUs support DDR4 up to 2933 MHz
* Core i5 / i3 / Pentium / Celeron CPUs support DDR4 up to 2666 MHz |
| Graphics | Requires Intel Processor with Intel HD Graphics |
| Audio | C-Media HS-100B USB Audio |
| LAN | 1 x Intel I219-V PHY Gigabit LAN |
| Storage | 4 x SATA3 6Gb/s supports RAID 0/1/5/10 with M.2 SATA (not when using PCIe NVMe SSD)
1 x M.2 (PCIe 3.0 x4 NVMe & SATA, M-key, 2242 2260 2280) |
| Super IO | FINTEK F81804U |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware | Intel fTPM 2.0 (PTT) Trusted Computing Firmware
Onboard NUVOTON TPM v2.0 |
| Back Panel Connectors |
1 +12V – 19V DC-in Jack (5.1 mm/ID and 7.4 mm/OD)
1 RJ45 LAN (10/100/1000)
3 USB 3.2 Gen 2 (10 Gb/s) Type-A
1 USB 3.2 Gen 1 (5 Gb/s) Type-C
1 DP 1.2 (4096 * 2304 @ 60Hz)
1 HDMI 1.4 (4096 * 2160 @ 30Hz)
2 3.5mm Audio Jack
|
| Onboard I/O Connectors |
1 PCI-E x4 Slot (Gen 3)
4 SATA3 6Gb/s Connector for RAID 0/1/5/10
1 M.2 M-Key, 2242 2260 2280 (PCIe x4 NVMe and SATA)
1 M.2 E-key, 2230 (USB and PCIe CNVi WiFi)
1 USB 3.2 Gen 1 (5 Gb/s) Headers for 2 additional USB 3.2 Ports
3 USB 2.0 Headers for 5 additional USB 2.0 Ports
1 Serial Headers (RS232/422/485)
1 24-bits Dual Channel LVDS Connector/Inverter
1 AT/ATX Mode Jumper
1 9-pin Front Audio Header
2 4-pin Fan Header
1 15-pin SATA Power out Connector
1 2-pin Alternate Power-in Connector
|
| Power Supply for MI09 |
External Power Supply – the board can be powered with a +12V ~ +19V external power supply though a DC connector on the back panel. The rear +12V ~ +19V DC jack accepts plugs with an inner diameter (ID) of 5.1 mm and an outer diameter (OD) of 7.4 mm, where the inner contact is +12V ~ +19V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V ~ +19V DC 1 x 2 power connector, where pins 2 is +12V ~ +19V (±5%) DC and pins 1 is GND. The internal 1 x 2 power connector is a Molex 5566-2 header which accepts a Molex 5557-02R connector from the power supply.
Caution: There is no isolation circuitry between the external +12V ~ +19V DC jack and the internal 1 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V ~ +19V DC jack is covered if the internal 1 x 2 power connector is to be used.
|
| Market Segments Supported |
√ Industrial PC
√ Factory Automation
√ Retail (POS/Kiosk/ATM)
√ Thin Client
√ Panel PC
√ IoT
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|
