| Model Name | MI02 |
| Part Number | MI02-40 | MI02-42 |
| Form Factor | Mini ITX (170 x 170mm) |
| Processor | 10th Gen Intel® Core i9 / i7 / i5 / i3 / Pentium / Celeron Processor up to 65W
11th Gen Intel® Core i9 / i7 / i5 Processor up to 65W
Socket LGA 1200 (Formerly Comet Lake and Rocket Lake) |
| Chipset | Intel H420E |
| Memory | 2 x 260-pin SODIMM Dual Channel DDR4-2933 up to 64GB Total
* Core i9 / i7 CPUs support DDR4 up to 2933 MHz
* Core i5 / i3 / Pentium / Celeron CPUs support DDR4 up to 2666 MHz |
| Graphics | Requires Intel Processor with Intel HD Graphics |
| Audio | Realtek ALC662 HD Audio Codec |
| LAN | 1 x Intel I225-LM PCIe 2.5GbE
1 x Intel I219-V PHY Gigabit LAN |
| Storage | 1 x M.2 (SATA, M-key, 2280) |
| Super IO | FINTEK F81966D |
| TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware | Intel fTPM 2.0 (PTT) Trusted Computing Firmware
Onboard NUVOTON TPM v2.0 |
| Back Panel Connectors |
4 USB 3.2 Gen 1 (5 Gb/s)
1 RJ45 LAN (10/100/1000)
1 RJ45 LAN (10/100/1000/2500)
1 DP 1.2 (4096 * 2304 @ 60Hz)
2 HDMI 1.4 (4096 * 2160 @ 30Hz)
2 3.5mm Audio Jack
1 +12V – 28V 2.5mm Diameter DC Power Jack
|
| Onboard I/O Connectors |
1 PCI-E x16 Slot (Gen 3, up to 2.1A 25W)
1 M.2 M-Key, 2280 (SATA only)
1 M.2 E-key, 2230 (USB and PCIe WiFi, doesn't support CNVi)
1 M.2 B-key, 3042 3052 (USB and PCIe for SIM Modem)
1 USB 2.0 Headers for 2 additional USB 2.0 Ports
4 Serial Headers (2 * RS232/422/485, 2 * RS232)
1 40-pin eDP (4096 * 2304 @ 60Hz, on bottom)
1 24-bits Dual Channel LVDS Connector/Inverter
1 Nano SIM Socket (on bottom)
1 8 bit GPIO Header
1 AT/ATX Mode Jumper
1 Chassis Intrusion Jumper
1 9-pin Front Audio Header
1 5-pin SMBUS Header
2 4-pin Fan Header
1 4-pin Alternate Power-in Connector
|
| Power Supply for MI02 |
External Power Supply – the board can be powered with a +12V ~ +28V external power supply though a DC connector on the back panel. The rear +12V ~ +28V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V ~ +28V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V ~ +28V DC 2 x 2 power connector, where pins 3 and 4 are +12V ~ +28V (±5%) DC and pins 1 and 2 are GND. The connector used is Molex Micro-Fit (3mm pitch), right-angled, 4-pos/dual row (2x2).
Caution: There is no isolation circuitry between the external +12V ~ +28V DC jack and the internal 2 x 2 power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V ~ +28V DC jack is covered if the internal 2 x 2 power connector is to be used.
|
| Market Segments Supported |
√ Industrial PC
√ Factory Automation
√ Retail (POS/Kiosk/ATM)
√ Panel PC
√ IoT
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|
