| Model Series | MF20 |
| Part Number | MF20-00 | MF20-07 (32GB eMMC and TPM 2.0)
MF20-08 (64GB eMMC and TPM 2.0) |
| Form Factor | 3.5" SBC (148 x 102mm) |
| Processor | Intel® Celeron J6412, 2.00GHz – 2.60GHz Burst, 4-Core 4-Thread, 10W TDP
* Ships with flat silver aluminum heatsink for direct attach |
| Memory | 1 x 260-pin Single Channel DDR4-3200 SO-DIMM up to 32GB Total |
| Graphics | Intel® UHD Graphics for 10th Gen Intel® Processors |
| Audio | Realtek ALC888S HD Audio |
| LAN | 2 x Intel I225-V PCIe 2.5GbE |
| Storage | 1 x SATA3 6Gb/s
1 x M.2 (SATA & PCIe 3.0 x2, M-key, 2242/2280 NVMe) | 1 x SATA3 6Gb/s
1 x M.2 (SATA & PCIe 3.0 x2, M-key, 2242/2280 NVMe)
Onboard 32/64GB eMMC |
| Super IO | FINTEK F81966D |
| TPM | Intel fTPM 2.0 (PTT) | Intel fTPM 2.0 (PTT)
Onboard NUVOTON TPM v2.0 |
| Back Panel Connectors |
1 3.5mm Combo Line-out/MIC Jack
2 HDMI 2.0b (4096 * 2160 @ 60Hz)
3 USB 3.2 Gen 2 (10 Gb/s)
3 USB 2.0 Port
2 RJ45 LAN (10/100/1000/2500)
1 +12V - 24V 2.5mm Diameter DC Power Jack
|
| Onboard I/O Connectors |
1 SATA3 6Gb/s Connector
1 M.2 M-Key, 2242/2280 (SATA & PCIe 3.0 x2 NVMe)
1 M.2 B-key, 3042 (USB 3.2 for 3G/LTE Modem)
1 M.2 E-key, 2230 (PCIe 3.0 x1/USB 2.0 for WiFi)
6 Serial Headers (5 * RS232, 1 * RS232/422/485)
2 USB Pin Headers for 4 additional USB 2.0 Ports
1 40-pin eDP (4096 * 2160 @ 60Hz)
1 24-bit Dual Channel LVDS/Inverter (1920 * 1080 @ 60Hz)
1 SIM Socket (Bottom)
1 8 bit GPIO Header
1 4-pin SMBUS Header
1 4-pin Fan Header
1 9-pin Front Audio Header
1 AT/ATX Mode Jumper
1 4-pin SATA Power Output (Male)
1 2-pin +12V – 24V Alternate Power-In (Mating plug: JST VHR-2N or TE 1-1123722-2)
|
| Power Supply for MF20 |
External Power Supply – the board can be powered with a +12V – 24V external power supply though a DC connector on the back panel. The rear +12V – 24V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm, where the inner contact is +12V – 24V and the shell is GND.
Internal Power Supply – the board can alternatively be powered via the internal +12V – 24V 2-pin power connector, where pin 1 is +12V – 24V and pin 2 is GND. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 connector from the power supply.
Caution: There is no isolation circuitry between the external +12V – 24V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V – 24V DC jack is covered if the internal 2-pin power connector is to be used.
|
| Market Segments Supported |
√ Industrial PC
√ Factory Automation
√ Retail (POS/Kiosk/ATM/Digital Signage)
√ Digital Security / Surveillance
√ Panel PC
|
| Environment |
Operating Temperature : 0 ~ 60°C
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|
