Model Series | F35-ASL1 |
Part Number | F35-ASL1-74330010 | F35-ASL1-74330810 (64GB eMMC and TPM 2.0) |
Form Factor | 3.5" SBC (148 x 102mm) |
Processor | Intel® Atom® x7433RE Processor, Formerly Amston Lake (TDP 9W) * Ships with flat silver aluminum heatsink for direct attach |
Graphics | Intel® UHD Graphics |
Memory | 1 x Non-ECC DDR5 4800 MT/s SODIMM up to 32GB |
Audio | Realtek ALC897 HD Audio and 3W Amplifier |
LAN | 2 x Intel I226-V 2.5GbE |
Storage | 1 x SATA3 6Gb/s 1 x M.2 2280 (PCIe 3.0 x2 NVMe, M-key) | 1 x SATA3 6Gb/s 1 x M.2 2280 (PCIe 3.0 x2 NVMe, M-key) 64GB eMMC |
Super IO | FINTEK F81966D |
TPM | Intel fTPM 2.0 (PTT) Trusted Computing Firmware | Intel fTPM 2.0 (PTT) Trusted Computing Firmware Onboard NUVOTON TPM v2.0 |
Back Panel Connectors |
1 12V ~ 28V 2.5mm Diameter DC Power Jack
2 HDMI 2.0b (4096 x 2160 @ 60Hz)
1 USB 3.2 Gen 2x1 (10 Gb/s)
1 USB 3.2 Gen 2x1 Type-C (10 Gb/s) with DP 1.4 (4096 x 2160 @ 60Hz)
4 USB 2.0
2 RJ45 2.5GbE LAN (10/100/1000/2500)
1 3.5mm Audio Jacks (Line-Out / Mic-In)

|
Onboard I/O Connectors |
1 SATA3 6Gb/s Connector
1 M.2 M-Key, 2280 (PCIe 3.0 x2 NVMe)
1 M.2 E-key, 2230 (USB2.0/PCIe 3.0 x1/CNVi)
1 M.2 B-key, 3042 3052 (USB3.2/2.0 for Cellular)
2 USB Headers for 4 additional USB 2.0 Ports
6 Serial Headers (5 * RS232, 1 * RS232/422/485)
1 24-bits Dual Channel LVDS/eDP (1920x1080 @60Hz)
1 Nano SIM Socket
1 8 bit GPIO Header
1 AT/ATX Mode Jumper
1 9-pin Front Audio Header
1 Speaker Header
1 5-pin SMBUS Header
1 Fan Header
1 4-pin SATA Power Output (Male)
1 2-pin +12V – 28V Alternate Power-In (Mating plug: JST VHR-2N or TE 1-1123722-2)
|
Power Supply for F35-ASL1 |
External Power Supply – the board can be powered with a +12V ~ +28V external power supply though a DC connector on the back panel. The rear +12V ~ +28V DC jack accepts plugs with an inner diameter (ID) of 2.5 mm and an outer diameter (OD) of 5.5 mm.
Internal Power Supply – the board can alternatively be powered via the internal +12V – 28V 2-pin power connector, where pin 1 is +12V – 28V and pin 2 is GND. The internal 2-pin power connector accepts a JST VHR-2N or TE 1-1123722-2 connector from the power supply.
Caution: There is no isolation circuitry between the external +12V ~ +28V DC jack and the internal 2-pin power connector. It is the system integrator's responsibility to ensure no more than one power supply unit is or can be attached to the board at any time and to ensure the external +12V ~ +28V DC jack is covered if the internal 2-pin power connector is to be used.
|
Market Segments Supported |
√ Edge Computing
√ Digital Signage
√ Industrial PCs
√ Factory Automation
√ Smart Cities
√ Digital Security
√ Surveillance Application
|
Environment |
Operating Temperature : -20 ~ 60°C
Storage Temperature : -20 ~ 85°C
Humidity: 10% ~ 90% RH @40°C (non-condensing)
|